SVCI J2534 IDS Online PATS Programming for Ford Kuga/Escape

This post show you guide on how to use SVCI J2534 to perform online PATS programming for Ford Kuga/Escape.

 

Procedures:

Connect SVCI J2534 interface to car OBD port and your pc,then run SVCI J2534 software.

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-1

Select “Start New Session”–>”All other”,then click “OK”

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-2

After vehicle identification,it will show you vehicle information as below,click “Yes” to continue

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-3

Check odometer value,click “Ok” continue

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-4

Select “Body”–>”Security”–>”PATS Functions”,and then click “OK”

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-5

Turn ignition to the ON position

Note:To perform the Program Additional Ignition Key function,you have to gain security access using the additional ignition key.If the vehicle is equipped with a pushbutton start,continue with testing even if the ignition is turned off.

Click “OK” icon

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-6

It will ask you “Is the vehicle is equipped with pushbutton start”,click “NO”

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-7

Then check your vehicle VIN and click “Yes” to continue

Now select “Parameter Reset (BCM/ABS/PCM)”,then click “OK” icon

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-8

Connection to the internet is required.

You may be prompted to enter your user identification and password

Click “Yes”

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-9

It will pop-up website,click “Login via WSLx”

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-10

Now please input your username and password

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-11

After then it will show you obtained data from internet successfully,click “OK” icon

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-12

Security Access Granted

You are about to perform Parameter Reset,click “YES” to continue

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-13

Turn the ignition to the OFF position,the wait proceed

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-14

After the it ask you to turn ignition to the ON postion

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-15

Open the driver side door.Close and lock all doors then wait until the vehicle console completely shuts off.If the engine still cannot start,disconnect the battery and wait for 10 minutes before reconnect

Test Complete

Press tick in exit.

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-16

Turn the ignition to the OFF position

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-17

Now back to menu to select “Selt test”–>”All CMDTCs”

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-19

Heading Continuous DTCs

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-20

DTCs show as below,turn on ignition and select it and click “Clear”

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-20 SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-21

 

Now read the DTCs again

SVCI-J2534-IDS-Online-PATS-Programming-for-Ford-Kuga-22

Done!

http://www.uobdii.com/wholesale/fvdi-j2534.html