Here UOBD2 show the PSA Diagbox 9.12 software download link,and here also share the procedures on how to install PSA Diagbox 9.12 software.But this version it have not bee tested,it can not work on your interface 100%.And if you want to get a 100% solution,you can check here: LEXIA 3 cable include software v7.8.3 tested 100% work!
Note:Here is new version installation guide:New Diagbox 9.23 Installation: Windows 10 or Windows 7? 32 bits or 64 bit?
For a stable Lexia 3 software,Diagbox V7.49 Software is recommended,tested 100 work!
Latest version: Diagbox_setup_v09.12.exe:
Diagbox v09.12 original and unchanged.
maybe of use to someone for personal research and development.
it is offered as is and with no support from myself.
Tested version: Diagbox v7.83 tested ok with Lexia 3 clone
HW & SW requirements：
Intel Celeron/Pentium III 400 MHz,
128 MB RAM,
50MB free HDD space
USB 1.1 port (USB 2.0 recommended)
Microsoft Windows 98 SR2/2000/XP with the latest service pack installed; Windows?XP?system better.
Please setup the software according to the requirements to hardware and software. Otherwise it will fail to setup and bring you much trouble.
Beforehand, plug your computer to the mains power supply and check that you have an internet connection. è
DiagBox will remain usable at the same time as the download of the installer (may take some time depending on your internet bandwidth).
Note: If you try to download Diagbox again, you will see the following error message
Step 2: Once the Digagbox download is complete, return to the desktop, double-click on the file named « DiagBox_setup_V09.12.exe »
First, close DiagBox, plug your computer to the mains power supply, check that you have an internet connection.
Select your language if necessary in the first step. After that, an intermediate validation message is displayed. Click on “Install” button:
Please wait until the end of the installation. About 30 min to perform all installations.
Depending on the options subscribed, after the activation procedure using your RRDI code, more steps will be necessary.
Diagbox Error “0” is due to no network card detected.
You must activate the network card ; that is, you have to disconnect the wifi then connect the internet cable of your box rj45 to the computer then you will be able to activate diagbox (to be activated diagarious of scari01 a besoing of a connection to the computer by cable network no wifi) A faith activate you will be able to finish the installation is possible to use diagbox even without
To avoid Diagbox software activation error and Windows XP installation issues, you’d better spend a bit on a crack but tested version Diagbox 7.83: http://www.uobdii.com/wholesale/diagbox-v601-software-for-lexia-3-pp2000.html, cost $9.99 only. Installed on XP system and works good.
Diagbox 7.83 how to use:
The video is used for Diagbox 7.83 tested version. Used with Lexia 3 china clone
Diagbox running on PSA Lexia cable is used for fault codes read and write, programming and enabling hidden functions, ECU reset, actuator test, auto- scanning…
In this video you will learn how to use diagbox, learn how to read faults, how to clear faults, how to read learnings keys , how to read all settings, how to reset oil gauge, reset maintenance gauge, read oil temperature, read gear values, test all parts of your car, change the driver settings, know what is the programmed settings, watch the whole video to know all the menus of the diagbox, you can move from one window to others, easy and fast. know how many remote key programmed to work with PSA cars
Diagbox 7.83 vehicle coverage:
Peugeot: 107, 206, 207, 307, 308, RCZ, 407, 508, 607, 1007, 3008, 4007, 5008, BIPPER, PARTNER, EXPERT, BOXER, 106, 205, 306, 309, 405, 406, 605, 806, 807 etc.
Citroen: C1, C2, C3 DS3, C4, DS4, C5, C6, C8, C-CROSSER, NERO, BERLINGO, JUMPY, AX, SAXO, BX, ZX, XSARA, XANTIA, XM, EVASION, C15, C-ZERO etc.
Took hours and hours to install the software, but afterwards it all works well. Read a few forums regarding the correct version of the software to install, you only need to go up to a certain point – after that the software gets more difficult to get to work properly. I use it on a 2012 DS3 to recalibrate the steering sensor and it works a treat.
This is an older version and you have to realise that Diagbox is the actual software you need to install not lexia. But i got it to work on my grand picasso 2009 1.6hdi after alot of you tube videos. Just do not update it beyond v5.1.
Arrived on time, Already had software installed so only really purchased for the lead which worked fine after simple install of drivers. my only disappointment was that it has no decals/stickers to distinguish the product but does not effect the use